Understanding Under-stitching

Under-stitching is an easy sewing technique; it’s a necessary technique if your garment has facings (versus bindings) on the neck, armholes, pant waistband, or the hem. Under-stitching keeps a facing from peeking out on the right side – that is it’s job.   The images of my purple printed tunic show straightforward under-stitching at the neckline; it becomes difficult when the facing is a one-piece for the neck and armholes as in the black/white tunic.  Wrong sides pictured below so you can see the facing up close.

normal understitch
Straight forward strip facing applied to a V-neck. Check the under-stitching line. Easy peasy.
inside facing
The one-piece version where the front and back neck and armhole are faced with one shaped facing.  Needs some tunneling action to under-stitch along the narrow armhole/shoulder area.

Basic under-stitching instruction:

Let’s take neck facing as a simple example. Sew the facing and garment together at the neck.  From the wrong side, trim seam allowance and press it toward the facing.  On the right side, lay it out flat and stitch as close as you can to the first seam – on the facing side, and through the seam allowance. This keeps the facing from peeking out on the right side.

peek inside
A peek under the facing.  
front
Under-stitching doing it’s job. I’m thrilled!

The story changes with a one-piece facing

Under-stitching can become difficult – almost impossible to do – in certain conditions. Like this one, where the front and back facings are actually one piece.  Know what I mean?  My purple printed tunic has a strip facing (which is much easier to do), whereas Vogue pattern 1550 (the black/white print) is an “all-in-one” facing. It means that the neck and armholes are faced with one whole piece – this one’s a different animal.  The V1550 pattern sewing guide has minimal instruction for the understitching step, as you can see in the image below.

guidesheet2

Let’s “unpack” this cryptic instruction, then see what can be done to reduce the stress you may be feeling at this point.

If you follow the instructions on the guide sheet, you would sew up the entire, “all-in-one” facing to the neck and then the armholes, and try to under-stitch the seams from the right side; except, the shoulders area is narrow, thus very difficult to get the seam under the presser foot – on a smaller size, this area is even narrower than my size 16 shoulder.  Ok, I agree that you can under-stitch as far as the presser foot will let you go, and stop midway. But, I managed to do it all around.

How I Under-stitched….

Below, I’m recapping how I managed to understitch all the seams, including those narrow areas.

  • Apply facing to the neckline only, (front and back) all around.  Under-stitch this as detailed above under basic instruction, before sewing the facing/armhole seam.
  • Sew up the armhole/facing seam, press as is.  Turn the all-in-one facing inside out through the shoulder and back seam, as in pattern instructions.
  • Now the tricky part: press the seam allowance toward the facing from the right side with a Clover miniature iron which is small enough and has a long handle to poke into the shoulder “tunnel”. If you do not have this miniature iron, do not stress. Use a regular iron as far as you can go. You can also finger press if your fabric is crisp and will respond to some finger pressing action.
small iron
Press the shoulder area “tunnel” with a mini-iron
Clover mini iron
Clover’s mini-iron (no affiliation)
  • Open the area by bunching up from the bottom of the facing to the shoulder seam; place under the presser foot (it gets bunchy behind the presser foot, but its do-able), and stitch a line on the facing as close to the seam as possible, starting from the shoulder seam and ending the side seam (side seams have not been sewn together yet).  Go slowly, and manipulate with fingers to keep the sewing area flat.  You’ve just under-stitched one side of the armhole; turn around the top and do the same bunchy thing – starting from the shoulder seam and ending at the side seam.  Be sure that the under-stitch line is on the facing and the seam allowance underneath it. Repeat on the other armhole.   Is that clear as mud??

Well, I’ll leave you with an image of the complete black/white tunic. One day, I’ll write a review of this pattern.

Have a great summer!

Samina

 

6 thoughts on “Understanding Under-stitching

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s